AUTO DIAGNOSTIC  Cape Town     South Africa

        Import Agency for more than 100 Diagnostic Tools and Equipment to the Motor Trade          

                                Inquiries or sales               

                 Cape Town - Chris Mengel:    Tel. 021 556 0146    074 240 6404     e-mail: chris@autodiagnostic.co.za

                                                                                                             BACK TO HOME PAGE

                                                                                                        CITROEN - PEUGEOT

    LEXIA 3-6 Citroen - Peugeot with cables interface   R 6, 880   (PL)  including software, cable kit and carry case.      User Manual

 

  

 

Description:

Dealer diagnostic scanner for comprehensive Citroen and Peugeot cars diagnostic. You can do all as a authorized dealer does. This diagnostics software allows you to perform complete diagnostics of all from 1995 until present models. Diagnostics is performed via OBD-II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001).

 

Supported functions:

Unlike other universal car scanner tools which only read fault codes, this software performs nearly ALL the functions like the original dealer diagnostic tool. Our diagnostic interface contains K-Line multi plexor, CAN-BUS interfaces and SAE J1850 bus (both PWM and VPW).

The following diagnostic functions are supported:

 

Read identification:

Auto-scan (complete car scan/test)

Read fault codes.

Clear fault codes.

Program supports report printing or copy to clipboard.

This function clears all stored fault codes and other diagnostic information.
Displays complete identification of control unit, e.g. part number, software/hardware version, manufacturer.

Displays all stored and pending fault codes with complete description (e.g. "Rail pressure - too low pressure").

Detects all ECUís (electronic control units) installed in car and reads all diagnostic fault codes.

 

Dealer diagnostic scanner for comprehensive Citroen and Peugeot cars diagnostic. You can do all as a authorized dealer does.This diagnostics software allows you to perform complete diagnostics of all from 1995 untill present models. Diagnostics is performed via OBD-II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001). Supported functions Unlike other universal car scanner tools which only read fault codes, this software performs nearly ALL the functions like the original dealer diagnostic tool. Our diagnostic interface contains K-Line multiplexor, CAN-BUS interfaces and SAE J1850 bus (both PWM and VPW). The following diagnostic functions are supported: Read identification Displays complete identification of control unit, e.g. part number, software/hardware version, manufacturer, etc... Read fault codes Displays all stored and pending fault codes with complete description (e.g. "Rail pressure - too low pressure"). Program supports report printing or copy to clipboard. Clear fault codes This function clears all stored fault codes and other diagnostic information. Auto-scan (complete car scan/test) Detects all ECUs (electronic control units) installed in car and reads all diagnostic fault codes. Measured Values Program displays live Data like Engine Speed, Battery voltage, Oxygen Sensor, Coolant Temperature, etc. Values can be displayed in graph, 9 values at once, or full listing (all measured values). Logging to file is also supported, which allows offline analysis. Actuator test Actuator test activates particular actuator (e.g. turn on fuel pump, lock/unlock wheel, lock/unlock doors, cut off fuel, etc..) Programming functions/Adaptation This feature is of great importance in all vehicles because systems like Engine control units, Immobilizers, Airbags, Alarms, Body Control Units, and some others, require you to perform reset or programming procedures after car repair is done, or even configuration after replacing broken Control Unit. Hardware and software requirements Software requires at least Intel Celeron/Pentium III 400 MHz, 128 MB RAM, 50MB free HDD space and USB 1.1 port (USB 2.0 recommended) and Microsoft Windows 98 SR2/2000/XP with the latest service pack installed. If customer requires, we can prepare ready to work PC.

 

Measured Values:
Program displays live Data like Engine Speed, Battery voltage, Oxygen Sensor, Coolant Temperature, etc. Values can be displayed in graph, 9 values at once, or full listing (all measured values). Logging to file is also supported, which allows offline analysis.

 

Actuator test:
Actuator test activates particular actuator (e.g. turn on fuel pump, lock/unlock wheel, lock/unlock doors, cut off fuel, etc..)

Programming functions/Adaptation
This feature is of great importance in all vehicles because systems like Engine control units, Immobilisers, Airbags, Alarms, Body Control Units, and some others, require you to perform reset or programming procedures after car repair is done, or even configuration after replacing broken Control Unit.

 

Hardware and software requirements:
Software requires at least Intel Celeron/Pentium III 400 MHz, 128 MB RAM, 50MB free HDD space and USB 1.1 port (USB 2.0 recommended) and Microsoft Windows 98 SR2/2000/XP with the latest service pack installed.

 

Set includes:
Main unit with OBD-2 cable kit
USB cable
Software CD

 

NB: Software is loaded on all above units and tested before

 

                                                                                          THIS PAGE TOP